TIPS ABOUT HOW TO Extend Smok Pen Recharge Time
The Smok Pen is really a new pen that was developed by two guys in California. They wanted to develop a cool writing instrument that appeared as if a real pen but had the opportunity to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has had the market by storm.
The Smok Pen includes a built quality that’s just great. I came across that even though it is an electronic pen the build quality is just as good as the pens that I have reviewed. This is because of how they made the most notable cap. You don’t need to worry about the cap cracking or breaking on you Smok Valve Pen.
Both biggest differences that separate the Smok Valve from other pens is the shape of the coils and just how that they are built. Generally the coil on a Smok Pen is bigger than on other pens. I believe that they did this on purpose, to help make the pen feel more substantial.
If you take a glance at a Smok Pen, you will observe that the body of the pen is round rather than smooth like other pens. On the back of the pen there exists a little tab that houses the coil. When you press on the tab it is simple to turn the heating element on / off. I must say i liked this feature because it allows me to use the Smok Pen 22 whenever I feel like smoking.
To utilize the Smok Pen you have to keep the heat button pressed. Once the button is pressed, the heating element will begin to warm up. Once it reaches the appropriate temperature it is possible to switch off the heating element. Smok recommends using a 22mm Element Vape Coupon tank. I prefer a larger tank, but that’s just me.
When you put your Smok Pen in to the tank you will notice a indicator light come on. The indicator light will stay green unless you put your Smok Pen into the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. You should always put your pen in to the charger before you apply the e-liquids to the coil heads. It is also important to do this before putting your e-liquids into the coil heads.
After you have completed this step, it is best to check to see in case you are at the right temperature for the coils to fire. Or even then you should turn the energy off and try again. Should you be still not satisfied with your Smok Pen i quickly suggest you take it set for some troubleshooting. This is what I would call the “troubleshooting process” because sometimes things just do not work as they should. I suggest that you perform the following two steps, then go on and check the Smok Pen to see if it still gets the electronic charging port.
Prior to going any further you should remove the battery from your pen and unscrew the magnetic cap. You should then remove the plastic sleeve that holds the sub-ohm. There exists a wire that runs through the Smok’s body which is green in color. You should loosen this wire using pliers. Once you have loosened this wire after that you can access the sub-ohm. You should then remove the wire from the Smok’s body and carefully insert it into the Smok pen’s electrical port, being careful to not touch any of the coils.
Once you have placed the sub-ohm tank in to the pen you should then place all of those other components like the wattage, the batteries and the heating element in to the included microwaveable microwave oven. Start the power and follow the on screen instructions. You need to place the pen’s battery in to the microwave and activate the setting. You need to then wait approximately 30 seconds before turning it cool off. When you first put the pen in to the microwave the electronic reading will show a minimal voltage protection setting. If this setting will not automatically get set you then should follow the on screen instructions.
After the Smok Pen has already reached the temperature that it needs to reach you should then connect the two wires to the positive and negative on the positive post on the Smok unit. You need to then connect another end of the battery to the negative post on the negative side of the Smok unit. The ultimate step would be to connect the positive cable to underneath of the Smok’s on / off switch.
After all of the components have been placed in to the pen, you should turn the energy on. Following the first test run, you ought to be able to start to see the battery life indicator light come on. If you don’t see any sign of life from the Smok Pen, you should take away the battery from the pen and replace it with a brand new one. For your convenience there is also a green light that could be pressed to be able to confirm the battery charging status. If you have done these things and you do not see the green light indicating charging, you should replace the battery.